Physical Properties | Metric | English | Comments |
|
Density | 1.25 g/cc | 0.0452 lb/in³ | ASTM D 792 |
Water Absorption | 0.12 % | 0.12 % | 24 hours @ 73F; ASTM D 570 |
Water Absorption at Saturation | 0.31 % | 0.31 % | Equilibrium, 73F; ASTM D 570 |
Linear Mold Shrinkage | 0.002 - 0.004 cm/cm | 0.002 - 0.004 in/in | Flow, 0.125 inch; ASTM D 955 |
Mechanical Properties |
|
Hardness, Rockwell M | 85 | 85 | ASTM D 785 |
Hardness, Rockwell R | 124 | 124 | ASTM D 785 |
Tensile Strength @ Break | 55.2 MPa | 8000 psi | Type I, 0.2 in/min; ASTM D 638 |
Tensile Strength @ Yield | 66.2 MPa | 9600 psi | Type I, 0.2 in/min; ASTM D 638 |
Elongation at Break | 15 % | 15 % | Type I, 0.2 in/min; ASTM D 638 |
Elongation at Yield | 8 % | 8 % | Type I, 0.2 in/min; ASTM D 638 |
Flexural Modulus | 3.45 GPa | 500 ksi | 0.05 in/min, 2" span; ASTM D 790 |
Flexural Yield Strength | 103 MPa | 15000 psi | 0.05 in/min, 2" span; ASTM D 790 |
Fatigue Strength | 13.8 MPa | 2000 psi | Fatigue Limit, 2.5 MM cycles; ASTM D 671 |
Izod Impact, Unnotched | 21.4 J/cm | 40 ft-lb/in | 73F; ASTM D 4812 |
Tensile Impact Strength | 158 kJ/m² | 75 ft-lb/in² | Type "S"; ASTM D 1822 |
Falling Dart Impact | 102 J | 75 ft-lb | 73F; ASTM D 3029 |
Taber Abrasion, mg/1000 Cycles | 11 | 11 | CS-17, 1 kg; ASTM D 1044 |
Izod Impact, Notched | 1.07 J/cm | 2 ft-lb/in | 73F; ASTM D 256 |
Electrical Properties |
|
Volume Resistivity | Min 1e+017 ohm-cm | Min 1e+017 ohm-cm | ASTM D 257 |
Dielectric Constant | 3.05 | 3.05 | 1 MHz; ASTM D 150 |
Dielectric Constant | 3.1 | 3.1 | 60 Hz; ASTM D 150 |
Dielectric Strength | 17.7 kV/mm | 450 V/mil | in air, 125 mils; ASTM D 149 |
Dissipation Factor | 0.0008 | 0.0008 | 60 Hz; ASTM D 150 |
Dissipation Factor | 0.0075 | 0.0075 | 1 MHz; ASTM D 150 |
Arc Resistance | Max 60 sec | Max 60 sec | Tungsten (+/- 0.125 inch); PLC Code 7; ASTM D 495 |
Comparative Tracking Index | 100 - 175 V | 100 - 175 V | (+/- 0.125 inch); PLC Code 4; UL 746A |
Hot Wire Ignition, HWI | 60 - 120 sec | 60 - 120 sec | (+/- 0.125 inch); PLC Code 1; UL 746A |
High Amp Arc Ignition, HAI | 60 - 120 arcs | 60 - 120 arcs | Surface (+/- 0.125 inch); PLC Code 1; UL 746A |
High Voltage Arc-Tracking Rate, HVTR | 80 - 150 mm/min | 3.15 - 5.91 in/min | (+/- 0.125 inch); PLC Code 3; UL 746A |
Thermal Properties |
|
CTE, linear 68°F | 32.4 µm/m-°C | 18 µin/in-°F | Flow, -40F to 200F; ASTM E 831 |
Specific Heat Capacity | 1.21 J/g-°C | 0.29 BTU/lb-°F | ASTM C 351 |
Thermal Conductivity | 0.2 W/m-K | 1.39 BTU-in/hr-ft²-°F | ASTM C 177 |
Deflection Temperature at 0.46 MPa (66 psi) | 146 °C | 295 °F | 0.250 inch, unannealed; ASTM D 648 |
Deflection Temperature at 1.8 MPa (264 psi) | 142 °C | 288 °F | 0.250 inch, unannealed; ASTM D 648 |
Vicat Softening Point | 154 °C | 310 °F | Rate B; ASTM D 1525 |
UL RTI, Electrical | 120 °C | 248 °F | UL 746B |
UL RTI, Mechanical with Impact | 110 °C | 230 °F | UL 746B |
UL RTI, Mechanical without Impact | 125 °C | 257 °F | UL 746B |
Flammability, UL94 | V-0 | V-0 | 0.028 in. |
Flammability, UL94 | 7 | 7 | 0.118 in. |
Oxygen Index | 36 % | 36 % | ASTM D 2863 |
Descriptive Properties |
|
UL File Number, USA | E121562 | |
UV-light, water exposure/immersion | F1 | UL746C |