| Physical Properties | Metric | English | Comments |
|
| Density | 1.53 g/cc | 0.0553 lb/in³ | ASTM D 792 |
| Density | 1.53 g/cc | 0.0553 lb/in³ | ISO 1183 |
| Filler Content | 30 % | 30 % | ASTM D 229 |
| Water Absorption | 0.06 % | 0.06 % | 24 hours; ASTM D 570 |
| Moisture Absorption at Equilibrium | 0.06 % | 0.06 % | (23 C / 50% RH) 1L; ISO 15512 |
| Water Absorption at Saturation | 0.26 % | 0.26 % | 23C; ISO 62 |
| Linear Mold Shrinkage | 0.003 - 0.007 cm/cm | 0.003 - 0.007 in/in | Flow; ASTM D 955 |
| Linear Mold Shrinkage, Transverse | 0.005 - 0.01 cm/cm | 0.005 - 0.01 in/in | ASTM D 955 |
| Melt Flow | 12 g/10 min | 12 g/10 min | cm3/10min; Melt Volume Rate, MVR at 250C/2.16 kg; ISO 1133 |
Mechanical Properties |
|
| Hardness, Rockwell R | 118 | 118 | ISO 2039/2 |
| Hardness, H358/30 | 122 MPa | 17700 psi | ISO 2039/1 |
| Tensile Strength, Ultimate | 115 MPa | 16700 psi | ASTM D 638 |
| Tensile Strength, Ultimate | 125 MPa | 18100 psi | 5 mm/min; ISO 527 |
| Elongation at Break | 2 % | 2 % | 5 mm/min; ISO 527 |
| Elongation at Break | 3 % | 3 % | ASTM D 638 |
| Tensile Modulus | 8 GPa | 1160 ksi | DIN 53457 |
| Tensile Modulus | 9.3 GPa | 1350 ksi | 1 mm/min; ISO 527 |
| Flexural Modulus | 7.5 GPa | 1090 ksi | DIN 53457 |
| Flexural Modulus | 8.5 GPa | 1230 ksi | 2 mm/min; ISO 178 |
| Flexural Strength | 190 MPa | 27600 psi | DIN 53452 |
| Flexural Strength | 195 MPa | 28300 psi | 2 mm/min; ISO 178 |
| Izod Impact, Notched | 1 J/cm | 1.87 ft-lb/in | 23 C; ASTM D 256 |
| Izod Impact, Notched (ISO) | 6 kJ/m² | 2.86 ft-lb/in² | 80*10*4 +23 C; ISO 180/ 1A |
| Izod Impact, Unnotched (ISO) | 45 kJ/m² | 21.4 ft-lb/in² | 80*10*4 +23 C; ISO 180/ 1U |
| Izod Impact, Unnotched Low Temp (ISO) | 45 kJ/m² | 21.4 ft-lb/in² | 80*10*4 -30 C; ISO 180/ 1U |
| Izod Impact, Notched, Low Temp | 0.95 J/cm | 1.78 ft-lb/in | at -40 C; ASTM D 256 |
| Izod Impact, Notched, Low Temp (ISO) | 5 kJ/m² | 2.38 ft-lb/in² | 80*10*4 -30 C; ISO 180/ 1A |
| Izod Impact, Notched, Low Temp (ISO) | 5 kJ/m² | 2.38 ft-lb/in² | 80*10*4 -40 C; ISO 180/ 1A |
| Charpy Impact Unnotched | 4.5 J/cm² | 21.4 ft-lb/in² | 23C, Unnotch Edgew 80*10*4 sp=62; ISO 179/1eU |
| Charpy Impact, Notched, Low Temp | 0.5 J/cm² | 2.38 ft-lb/in² | at -30C, V-notch Edgew 80*10*4 sp=62; ISO 179/1eA |
| Charpy Impact, Unnotched Low Temp | 4.5 J/cm² | 21.4 ft-lb/in² | at -30C, Unnotch Edgew 80*10*4 sp=62; ISO 179/1eU |
| Charpy Impact, Notched | 0.5 J/cm² | 2.38 ft-lb/in² | 23C, V-notch Edgew 80*10*4 sp=62; ISO 179/1eA |
| Taber Abrasion, mg/1000 Cycles | 19 | 19 | CS-17, 1 kg; GE Test |
Electrical Properties |
|
| Volume Resistivity | Min 1e+015 ohm-cm | Min 1e+015 ohm-cm | IEC 60093 |
| Surface Resistivity per Square | Min 1e+015 ohm | Min 1e+015 ohm | ROA; IEC 60093 |
| Dielectric Constant | 3.1 | 3.1 | 1 MHz; IEC 60250 |
| Dielectric Constant | 3.1 | 3.1 | 50 Hz; IEC 60250 |
| Dielectric Strength | 16 kV/mm | 406 kV/in | in oil, 3.2 mm; IEC 60243-1 |
| Dielectric Strength | 19 kV/mm | 483 kV/in | Short time, 1.0 mm; IEC 60243-1 |
| Dielectric Strength | 19 kV/mm | 483 kV/in | Short time, 3.2 mm; ASTM D 149 |
| Dielectric Strength | 24 kV/mm | 610 kV/in | in oil, 1.6 mm; IEC 60243-1 |
| Dielectric Strength | 28 kV/mm | 711 kV/in | in oil, 0.8 mm; IEC 60243-1 |
| Dissipation Factor | 0.001 | 0.001 | 50 Hz; IEC 60250 |
| Dissipation Factor | 0.01 | 0.01 | 1 MHz; IEC 60250 |
| Arc Resistance | 146 sec | 146 sec | Tungsten; ASTM D 495 |
| Comparative Tracking Index | 275 V | 275 V | Stand. Black; IEC 60112/3rd |
| Comparative Tracking Index | 300 V | 300 V | IEC 60112/3rd |
| Comparative Tracking Index | 425 V | 425 V | Electr Grey; IEC 60112/3rd |
| Hot Wire Ignition, HWI | 63 sec | 63 sec | UL 746A |
| High Amp Arc Ignition, HAI | 112 arcs | 112 arcs | on surface; UL 746A |
| High Voltage Arc-Tracking Rate, HVTR | 0.6 mm/min | 0.0236 in/min | UL 746A |
Thermal Properties |
|
| CTE, linear 20°C | 25 µm/m-°C | 13.9 µin/in-°F | 23C-80C, flow; ISO 11359-2 |
| CTE, linear 20°C Transverse to Flow | 120 µm/m-°C | 66.7 µin/in-°F | 23C-80C; ISO 11359-2 |
| Thermal Conductivity | 0.19 W/m-K | 1.32 BTU-in/hr-ft²-°F | ISO 8302 |
| Deflection Temperature at 0.46 MPa (66 psi) | 215 °C | 419 °F | ASTM D 648 |
| Deflection Temperature at 0.46 MPa (66 psi) | 220 °C | 428 °F | HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm; ISO 75/Be |
| Deflection Temperature at 1.8 MPa (264 psi) | 200 °C | 392 °F | HDT/Ae, 1.82 MPa Edgew 120*10*4 sp=100mm; ISO 75/Ae |
| Deflection Temperature at 1.8 MPa (264 psi) | 205 °C | 401 °F | ASTM D 648 |
| Vicat Softening Point | 213 °C | 415 °F | VST/A/120; DIN 53460 |
| Vicat Softening Point | 215 °C | 419 °F | B/50; ISO 306 |
| Vicat Softening Point | 215 °C | 419 °F | B/120; ISO 306 |
| Vicat Softening Point | 222 °C | 432 °F | Rate B; ASTM D 1525 |
| Vicat Softening Point | 223 °C | 433 °F | A/50; ISO 306 |
| UL RTI, Electrical | 140 °C | 284 °F | UL 746B |
| UL RTI, Mechanical with Impact | 140 °C | 284 °F | UL 746B |
| UL RTI, Mechanical without Impact | 140 °C | 284 °F | UL 746B |
| Flammability, UL94 | HB | HB | 0.84 mm |
| Glow Wire Test | 750 °C | 1380 °F | Passes at 1 mm; EDF HN60S02 |
| Glow Wire Test | 750 °C | 1380 °F | Passes at 1 mm; IEC 60695-2-1 |
Descriptive Properties |
|
| Ball Pressure Test, 125 C +/- 2 C | PASSES | IEC 60035-1 |
| Hot Mandrel Test, 300 C | PASSES | CEE10/IIed |
| Water Absorption, 24 hours, mg | 6 | DIN 53495 |
|
 Printer friendly version |
English 
